HomePneumatic Fittings
PB Pneumatic Male Thread Tee Fitting

PB Pneumatic Male Thread Tee Fitting

2026-04-28

Specification Parameters Operating Fluid Air Type Pneumatic Fittings Proof Pressure 1.32 MPa (13.5 kgf/cm²) Max. Operating Pressure 0~0.9 MPa (0~9.2 kgf/cm²) Ambient & Fluid Temperature 0~60°C Applicable Tubing PU Tube, Nylon Tube Model ΦD×2 E B ΦP×2 A R H PB4-M5 4 21.5 36 11 3.5 M5 10 PB4-01 4 25 36 11 7 R1/8 10 PB4-02 4 26 36 11 8 R1/4 14 PB6-M5 6 23.5 40 13 3.5 M5 12 PB6-01 6 27 40 13 7 R1/8 12 PB6-02 6 28 40 13 8 R1/4 14 PB6-03 6 29 40 13 9 R3/8 17 PB6-04 6 30.5 40 13 10 R1/2 21 PB8-01 8 29 44 15 7 R1/8 14 PB8-02 8 30 44 15 8 R1/4 14 PB8-03 8 31 44 15 9 R3/8 17 PB8-04 8 32.5 44 15 10 R1/2 21 PB10-01 10 32 52 18.5 7 R1/8 17 PB10-02 10 33 52 18.5 8 R1/4 17 PB10-03 10 34 52 18.5 9 R3/8 17 PB10-04 10 35.5 52 18.5 10 R1/2 21 PB12-01 12 34 56 21 7 R1/8 19 PB12-02 12 35 56...
PLF Pneumatic Female 90 Degree Elbow Fitting

PLF Pneumatic Female 90 Degree Elbow Fitting

2026-04-27

Specification Parameters Operating Fluid Air Type Pneumatic Fittings Proof Pressure 1.32 MPa (13.5 kgf/cm²) Max. Operating Pressure 0~0.9 MPa (0~9.2 kgf/cm²) Ambient & Fluid Temperature 0~60°C Applicable Tubing PU Tube, Nylon Tube Model ΦD E B ΦP A R H  PLF4-M5 4 18 18.5 11 4.5 M5 10 PLF4-01 4 18 22.5 11 8 R1/8 12 PLF4-02 4 18 24 11 9.5 R1/4 15 PLF6-M5 6 20 20.5 13 4.5 M5 12 PLF6-01 6 20 24.5 13 8 R1/8 12 PLF6-02 6 20 26 13 9.5 R1/4 15 PLF6-03 6 20 27 13 10.5 R3/8 19 PLF6-04 6 20 28 13 11.5 R1/2 24 PLF8-01 8 22 24.5 15 10.5 R1/8 14 PLF8-02 8 22 28 15 9.5 R1/4 15 PLF8-03 8 22 29 15 10.5 R3/8 24 PLF8-04 8 22 30 15 11.5 R1/2 19 PLF10-01 10 26 27.5 18.5 8 R1/8 17 PLF10-02 10 26 27.5 18.5 11 R1/4 17 PLF10-03 10 26 32 18.5 10.5 R3/8 19 PLF10-04 10 26 33 18.5 11.5 R1/2 24 PLF12-01 12 28 29.5 21 8 R1/8 19 PLF12-02 12 28 29.5...
PX Pneumatic Y-Type Male Thread Tee Fitting

PX Pneumatic Y-Type Male Thread Tee Fitting

2026-04-27

Specification Parameters Operating Fluid Air Type Pneumatic Fittings Proof Pressure 1.32 MPa (13.5 kgf/cm²) Max. Operating Pressure 0~0.9 MPa (0~9.2 kgf/cm²) Ambient & Fluid Temperature 0~60°C Applicable Tubing PU Tube, Nylon Tube Model ΦD×2 E P A R H PX4-M5 4 37 11 3.5 M5 10 PX4-01 4 40.5 11 7 R1/8 10 PX4-02 4 51.5 11 8 R1/4 14 PX6-M5 6 40 13 3.5 M5 12 PX6-01 6 43.5 13 7 R1/8 12 PX6-02 6 44.5 13 8 R1/4 14 PX6-03 6 45.5 13 9 R3/8 17 PX6-04 6 47 13 10 R1/2 21 PX8-01 8 47.5 15 7 R1/8 14 PX8-02 8 48.5 15 8 R1/4 14 PX8-03 8 49.5 15 9 R3/8 17 PX8-04 8 51 15 10 R1/2 21 PX10-01 10 51.5 18.5 7 R1/8 17 PX10-02 10 52.5 18.5 8 R1/4 17 PX10-03 10 53.5 18.5 9 R3/8 17 PX10-04 10 55 18.5 10 R1/2 21 PX12-01 12 54 21 7 R1/8 19 PX12-02 12 55 21 8 R1/4 19 PX12-03 12 56 21 9 R3/8 19 PX12-04 12 57.5 21 10 R1/2 21 PX14-02...
PD Pneumatic T-Type Side Thread Tee Fitting

PD Pneumatic T-Type Side Thread Tee Fitting

2026-04-27

Specification Parameters Operating Fluid Air Type Pneumatic Fittings Proof Pressure 1.32 MPa (13.5 kgf/cm²) Max. Operating Pressure 0~0.9 MPa (0~9.2 kgf/cm²) Ambient & Fluid Temperature 0~60°C Applicable Tubing PU Tube, Nylon Tube Model ΦD×2 E B ΦP×2 A R H PD4-M5 4 18 39.5 11 3.5 M5 10 PD4-01 4 18 43 11 7 R1/8 10 PD4-02 4 18 44 11 8 R1/4 14 PD6-M5 6 20 43.5 13 3.5 M5 12 PD6-01 6 20 47 13 7 R1/8 12 PD6-02 6 20 48 13 8 R1/4 14 PD6-03 6 20 49 13 9 R3/8 17 PD6-04 6 20 50.5 13 10 R1/2 21 PD8-01 8 22 50.5 15 7 R1/8 14 PD8-02 8 22 51.5 15 8 R1/4 14 PD8-03 8 22 52.5 15 9 R3/8 17 PD8-04 8 22 54 15 10 R1/2 21 PD10-01 10 26 58 18.5 7 R1/8 17 PD10-02 10 26 59 18.5 8 R1/4 17 PD10-03 10 26 60 18.5 9 R3/8 17 PD10-04 10 26 61.5 18.5 10 R1/2 21 PD12-01 12 28 62 21 7 R1/8 19 PD12-02 12 28 63...
PMF Pneumatic Bulkhead Female Straight Fitting

PMF Pneumatic Bulkhead Female Straight Fitting

2026-04-27

Specification Parameters Operating Fluid Air, Vaccum, Water(no freezing) Body Material Brass Type Pneumatic Fittings Proof Pressure 1.32 MPa (13.5 kgf/cm²) Max. Operating Pressure 0~0.9 MPa (0~9.2 kgf/cm²) Ambient & Fluid Temperature 0~60°C Lock Claw Stainless Steel(SUS) Applicable Tubing PU Tube, Nylon Tube   Model ΦD R A B H1 H2 M PMF4-M5 4 M5 5.5 24 14 14 M12×1 PMF4-01 4 R1/8 8 24 14 14 M12×1 PMF4-02 4 R1/4 9.5 27.5 15 14 M12×1 PMF6-M5 6 M5 5.5 25.5 15 17 M14×1 PMF6-01 6 R1/8 8 25.5 15 17 M14×1 PMF6-02 6 R1/4 9.5 29.5 15 17 M14×1 PMF6-03 6 R3/8 10.5 30 19 17 M14×1 PMF6-04 6 R1/2 11.5 31 24 17 M14×1 PMF8-01 8 R1/8 8 26 17 19 M16×1 PMF8-02 8 R1/4 9.5 26 17 19 M16×1 PMF8-03 8 R3/8 10.5 30.5 19 19 M16×1 PMF8-04 8 R1/2 11.5 31.5 24 19 M16×1 PMF10-01 10 R1/8 8 27.5 21 24 M20×1 PMF10-02 10 R1/4 9.5 27.5 21 24 M20×1 PMF10-03 10 R3/8 10.5 28 21 24 M20×1 PMF10-04 10 R1/2 11.5 29 24 24 M20×1 PMF12-01 12...
PCF Pneumatic Female Straight Fitting

PCF Pneumatic Female Straight Fitting

2026-04-27

Specification Parameters Operating Fluid Air, Vaccum, Water(no freezing) Body Material Brass Type Pneumatic Fittings Proof Pressure 1.32 MPa (13.5 kgf/cm²) Max. Operating Pressure 0~0.9 MPa (0~9.2 kgf/cm²) Ambient & Fluid Temperature 0~60°C Lock Claw Stainless Steel(SUS) Applicable Tubing PU Tube, Nylon Tube Model ΦD R A B H PCF4-M5 4 M5 5.5 19.5 10 PCF4-01 4 R1/8 8 22 12 PCF4-02 4 R1/4 9.5 23.5 15 PCF6-M5 6 M5 5.5 20.5 12 PCF6-01 6 R1/8 8 23.5 12 PCF6-02 6 R1/4 9.5 25 15 PCF6-03 6 R3/8 10.5 26 19 PCF6-04 6 R1/2 11.5 27 24 PCF8-01 8 R1/8 8 24 14 PCF8-02 8 R1/4 9.5 25.5 15 PCF8-03 8 R3/8 10.5 26.5 10 PCF8-04 8 R1/2 11.5 27.5 24 PCF10-01 10 R1/8 8 25 17 PCF10-02 10 R1/4 9.5 27 17 PCF10-03 10 R3/8 10.5 28 19 PCF10-04 10 R1/2 11.5 29 24 PCF12-01 12 R1/8 8 27 19 PCF12-02 12 R1/4 9.5 28.5 19 PCF12-03 12 R3/8 10.5 30 19 PCF12-04 12 R1/2 10.5 31 24 Key Features Push-to-connect quick installation design Female thread connection for internal ports Leak-proof...
PC Pneumatic Straight Fitting Series Push-in Tube to Thread Air Connectors

PC Pneumatic Straight Fitting Series Push-in Tube to Thread Air Connectors

2026-04-27

Specification Parameters Operating Fluid Air, Vaccum, Water(no freezing) Body Material Brass Type Pneumatic Fittings Proof Pressure 1.32 MPa (13.5 kgf/cm²) Max. Operating Pressure 0~0.9 MPa (0~9.2 kgf/cm²) Ambient & Fluid Temperature 0~60°C Lock Claw Stainless Steel(SUS) Applicable Tubing PU Tube, Nylon Tube  Model ΦD R A B H PC4-M5 4 M5 3.5 18.5 10 PC4-01 4 R1/8 7 19.5 10 PC4-02 4 R1/4 8 19 14 PC6-M5 6 M5 3.5 20 12 PC6-01 6 R1/8 7 21 12 PC6-02 6 R1/4 8 20 14 PC6-03 6 R3/8 9 21 17 PC6-04 6 R1/2 10 22 21 PC8-01 8 R1/8 7 23.5 14 PC8-02 8 R1/4 8 22.5 14 PC8-03 8 R3/8 9 21 17 PC8-04 8 R1/2 10 22 21 PC10-01 10 R1/8 7 25.5 17 PC10-02 10 R1/4 8 26.5 17 PC10-03 10 R3/8 9 25 17 PC10-04 10 R1/2 10 23 21 PC12-01 12 R1/8 7 27 19 PC12-02 12 R1/4 8 28 19 PC12-03 12 R3/8 9 26.5 19 PC12-04 12 R1/2 10 24 21 PC14-02 14 R1/4 8 29.5 21 PC14-03 14 R3/8 9 30.5 21 PC14-04...
PU Series Zinc Alloy Fittings

PU Series Zinc Alloy Fittings

2025-09-08

Tips for choosing a quick coupler 01: How to choose a quick coupler: 1. The connecting thread and pipe part are not allowed to pull or rotate, otherwise the thread or pipe connection will fall off. In the case of pulling or turning, a rotary joint should be used. 2. The bending of the pipe should be greater than the minimum bending radius, otherwise the pipe is easy to break. 3. Inflammable, explosive or toxic gases such as coal gas, gas fuel and refrigerant cannot be transported in the pipe 4. General industrial water can be used. 5. The impulse pressure should be prepared, not exceeding the maximum operating pressure, otherwise it is easy to damage. 02: How to install the quick connector? 1. Before installation, confirm the correct model and size, and confirm that the product has no cracks or scars. 2. The length of the connecting pipe will change considering the pressure change, so the length should be left margin. 3. The joint box tube is not allowed to be twisted or stretched, and bear a negative torque, so as to avoid...
PET Type Zinc Alloy Pneumatic Quick Push Fittings

PET Type Zinc Alloy Pneumatic Quick Push Fittings

2025-09-06

Tips for choosing a quick coupler 01: How to choose a quick coupler: 1. The connecting thread and pipe part are not allowed to pull or rotate, otherwise the thread or pipe connection will fall off. In the case of pulling or turning, a rotary joint should be used. 2. The bending of the pipe should be greater than the minimum bending radius, otherwise the pipe is easy to break. 3. Inflammable, explosive or toxic gases such as coal gas, gas fuel and refrigerant cannot be transported in the pipe 4. General industrial water can be used. 5. The impulse pressure should be prepared, not exceeding the maximum operating pressure, otherwise it is easy to damage. 02: How to install the quick connector? 1. Before installation, confirm the correct model and size, and confirm that the product has no cracks or scars. 2. The length of the connecting pipe will change considering the pressure change, so the length should be left margin. 3. The joint box tube is not allowed to be twisted or stretched, and bear a negative torque, so as to avoid...
C-type Quick Coupling for Air Compressor

C-type Quick Coupling for Air Compressor

2025-09-05

Tips for choosing a quick coupler 01: How to choose a quick coupler: 1. The connecting thread and pipe part are not allowed to pull or rotate, otherwise the thread or pipe connection will fall off. In the case of pulling or turning, a rotary joint should be used. 2. The bending of the pipe should be greater than the minimum bending radius, otherwise the pipe is easy to break. 3. Inflammable, explosive or toxic gases such as coal gas, gas fuel and refrigerant cannot be transported in the pipe 4. General industrial water can be used. 5. The impulse pressure should be prepared, not exceeding the maximum operating pressure, otherwise it is easy to damage. 02: How to install the quick connector? 1. Before installation, confirm the correct model and size, and confirm that the product has no cracks or scars. 2. The length of the connecting pipe will change considering the pressure change, so the length should be left margin. 3. The joint box tube is not allowed to be twisted or stretched, and bear a negative torque, so as to...
C-type self-locking plastic steel pneumatic joint

C-type self-locking plastic steel pneumatic joint

2025-09-04

Tips for choosing a quick coupler 01: How to choose a quick coupler: 1. The connecting thread and pipe part are not allowed to pull or rotate, otherwise the thread or pipe connection will fall off. In the case of pulling or turning, a rotary joint should be used. 2. The bending of the pipe should be greater than the minimum bending radius, otherwise the pipe is easy to break. 3. Inflammable, explosive or toxic gases such as coal gas, gas fuel and refrigerant cannot be transported in the pipe 4. General industrial water can be used. 5. The impulse pressure should be prepared, not exceeding the maximum operating pressure, otherwise it is easy to damage. 02: How to install the quick connector? 1. Before installation, confirm the correct model and size, and confirm that the product has no cracks or scars. 2. The length of the connecting pipe will change considering the pressure change, so the length should be left margin. 3. The joint box tube is not allowed to be twisted or stretched, and bear a negative torque, so as to avoid...
HRC pneumatic joint high-speed rotary joint

HRC pneumatic joint high-speed rotary joint

2025-09-03

01: How to choose a quick coupler: 1. The connecting thread and pipe part are not allowed to pull or rotate, otherwise the thread or pipe connection will fall off. In the case of pulling or turning, a rotary joint should be used. 2. The bending of the pipe should be greater than the minimum bending radius, otherwise the pipe is easy to break. 3. Inflammable, explosive or toxic gases such as coal gas, gas fuel and refrigerant cannot be transported in the pipe 4. General industrial water can be used. 5. The impulse pressure should be prepared, not exceeding the maximum operating pressure, otherwise it is easy to damage. 02: How to install the quick connector? 1. Before installation, confirm the correct model and size, and confirm that the product has no cracks or scars. 2. The length of the connecting pipe will change considering the pressure change, so the length should be left margin. 3. The joint box tube is not allowed to be twisted or stretched, and bear a negative torque, so as to avoid the joint damage, the tube...

ABOUT US SALES NETWORK CONTACT US CAREERS

For inquiries about our products or pricelist, please leave your email to us and we will be in touch within 24 hours.

Quick Links

Warranty policy

Quality Policy

Terms of Use

Cookies Policy

Privacy Policy

Contact

       

Email: [email protected]
Phone: +8613605806063
WhatsApp: Contact Now

Copyright © 2025, Wenzhou Hongmi Pneumatic Co., Ltd. All Rights Reserved.